Patents
Literature
Hiro is an intelligent assistant for R&D personnel, combined with Patent DNA, to facilitate innovative research.
Hiro

173 results about "Relative variation" patented technology

Relative variation refers to the spread of a sample or a population as a proportion of the mean. Relative variation is useful because it can be expressed as a percentage, and is independent of the units in which the sample or population data are measured.

Capacitive Position Sensor

A capacitive position sensor has a periodic array of electrodes which form capacitors between pairs of the electrodes. The location of a dielectric inhomogeneity in the vicinity of the sensor is determined by comparison of the relative change in the capacitance of the capacitors. The comparison may be carried out using a capacitive Wheatstone Bridge arrangement. The sensor configuration has the advantage that it is independent of the absolute value of the dielectric constant of the environment in which the sensor is located.
Owner:SCI GENERICS LTD

Reflected wave clock synchronization

A radar system has a phased-array antenna and plural local oscillators for controlling local transmit / receive units. The local oscillators are slaved to a master oscillator. The analog clock signal paths are subject to relative changes in electrical length. The electrical lengths of the signal paths are measured by phase-detecting forward- and reverse-direction clock signal flows. The phase-detected information for each signal path is a measure of the time delay. The radar command processor receives the measure of time delay and corrects the radar operation in response thereto.
Owner:LOCKHEED MARTIN CORP

Method of determining the gain characteristic of a distributed Raman amplifier

InactiveUS20050105167A1Accurate and simple to determineLaser detailsReflectometers using simulated back-scatterFiberAudio power amplifier
A method of determining the gain characteristic of a Raman amplifier includes the steps of launching a pump light signal into a fiber; preliminary adjusting the power of the pump light signal to a value that lies in a range where the amplified spontaneous emission noise originating from the pump light signal is substantially proportional to the on / off gain provided by the power of the pump light signal; monitoring the power of the amplified spontaneous emission noise signal; varying the power of the pump light signal; measuring a variation in the power of the amplified spontaneous emission noise signal corresponding to the pump power variation; and determining the gain characteristic of the amplifier from the relative variation in pump power and the measured variation in noise power.
Owner:ALCATEL LUCENT SAS

Method of Estimation of Traffic Information, Device of Estimation of Traffic Information and Car Navigation Device

There is provided a method and a device for accurately estimating traffic information of a link having no traffic information even if different types of roads are mixed. The device finds a parameter characterizing a damping curve of a quantity of change of relative speed based on stored traffic information for links on a city center side on a minimum-time cost route connecting the city center and suburbs, finds a quantity of change of relative speed of the link having no observed traffic information and estimates its traffic information based on the damping curve. The device also calculates a ratio of quantities of change of relative speed of two links whose road types change as a speed change similarity ratio and estimates traffic information of the link of a second road type from known traffic information of the link of a first road type by using that ratio.
Owner:CLARION CO LTD

Gesture recognition method and touch system incorporating the same

A gesture recognition method for a touch system includes the steps of: capturing images looking across a plate surface with at least one image sensor; processing the images to determine a contact state variation of a single pointer on the plate surface; and recognizing whether a relative variation between the single pointer and the plate surface matches a predetermined gesture when the contact state variation is larger than a threshold. The present invention further provides a touch system.
Owner:PIXART IMAGING INC

Particle-optical apparatus and method for operating the same

A particle-optical apparatus is proposed as well as a method for operating the same. The particle-optical apparatus provides a magnetic field for deflecting charged particles of a beam of charged particles and comprises a body of a material with a permeability number around which a current conductor at least partially engages and a temperature-adjusting unit -for adjusting a temperature of the magnetic-flux-carrying body substantially to a nominal temperature. A relative variation of the permeability number relative to a width of a temperature range is to be smaller than a limit value a, wherein a is preferably smaller than 3.10<-3>K<-1>. In particular, the nominal temperature is at an extremum of a temperature dependence of the permeability number. Preferably, such a particle-optical apparatus can be employed in a microscopy or a lithography apparatus.
Owner:CARL ZEISS SMT GMBH

Key-judging method for capacitive touch keys

The invention discloses a key-judging method for capacitive touch keys, comprising the steps of: setting an entropy coefficient; scanning keys to obtain a count value of the first charging time of a charge and discharge capacitor; dividing the count value of the first charging time into the entropy coefficient to obtain a first relative quantity reflecting the equivalent capacity of a touch key; scanning the keys again to obtain a count value of the second charging time of the charge and discharge capacitor; dividing the count value of the second charging time into the entropy coefficient to obtain a second relative quantity reflecting the equivalent capacity of the touch key; obtaining a difference value between the second relative quantity and the first relative quantity, and judging the keys by utilizing the difference value. In the key-judging method, the keys are judged by obtaining the relative variation quantity of the charging time of the charge and discharge capacitor C1. Therefore, the difference of stray capacitance on a PAD of a PCB cannot influence key judgement. The method is simple in realization and greatly reduces the requirements and the difficulty for PCB and software algorithm treatment.
Owner:SINO WEALTH ELECTRONICS

Self-calibration method for parallel robot

The invention discloses a self-calibration method of a parallel robot. The method comprises the following steps of: arranging a displacement sensor on each driving branch of the parallel robot, additionally arranging a measuring branch between a fixed platform and a movable platform of the parallel robot, arranging a rope sensor on the measurement branch, establishing a function relation between the relative variation of displacement of the drive branches and the measuring branch and parameters of pose of the movable platform and mechanism parameters of all the branches, driving the parallel robot to carry out pose transformation, enabling the number of established equations to be greater than or more to the number of the mechanism parameters to be identified, and carrying out numerical value solving to obtain poses of the movable platform in any state and mechanism parameter errors and further realize self-calibration. The self-calibration method has the advantage of low cost, convenience for operation and freedom from restriction of distance, hardly has restriction to mechanism design and is a good choice for calibration schemes of the parallel robots.
Owner:YANSHAN UNIV

Automatic evaporator defrosting on-off control method

The present invention is automatic evaporator defrosting on-off control method. The relative change in wind speed through the evaporator before and after the defrosting of the evaporator is used in controlling the start and the stop of defrosting. The method has the advantages of no need of measuring thickness of frost, no difficulty in measuring average thickness of frost layer, the reasonable determination of the defrosting on and off time based on only the air flow speed, and capacity of ensuring excellent heat transferring characteristic of the evaporator and the efficient operation of the refrigerating system.
Owner:XI AN JIAOTONG UNIV

Blood pressure measurement cuff wrapping control device and method

In wrapping a blood pressure measurement cuff enclosing therein a bladder, which is inflated when supplied with air, around a region for measurement, first, a predetermined amount of air is supplied to the bladder and then enclosed therein. Then, the blood pressure measurement cuff is wrapped around the region for measurement of a subject for the purpose of measuring his / her blood pressure. During this wrapping process, relative variations in the pressure in the bladder are sequentially detected. The time period in which the detection results indicate that the variation has not reached a predetermined threshold value, the wrapping proceeds. When the detection results indicate that the variation has reached the predetermined threshold value, the wrapping is terminated.
Owner:OMRON HEALTHCARE CO LTD

Method and device for judging optimal times of stroke of pumping unit

The invention discloses a method and a device for judging optimal the time of stroke of a pumping unit. The method comprises the following steps of: obtaining a current load displacement indicator diagram according to data of load and displacement sensors; changing the time of stroke, re-collecting the load displacement data to obtain the changed load displacement indicator diagram after the changing of the time of stroke; calculating relative liquid yield according to the ground indicator diagram before and after the changing of the time of stroke, judging the variation situation of the ratio of; and continuously running the programs until the minimal time of stroke is obtained under the maximal daily liquid yield, i.e., the optimal time of stroke is obtained. The device mainly comprises the load sensor, the angular displacement sensor, an RTU (remote terminal unit), a frequency changer, and on the like. Due to the fact that the optimal time of stroke judging program adopts the relative variation value of the daily liquid yield instead of the absolute value of the daily liquid yield, so the program is low in computing amount and small in occupied internal memory, and is capable of directly running on the RTU, further, the pumping unit can finish the data collection, computation and control independently by self without depending on the computation and the control of a host computer, and the system is ensured to run more reliably.
Owner:PETROCHINA CO LTD

Method of diagnosing a fault on a transformer winding

The present invention relates to a method of diagnosing a fault on a transformer winding by using frequency response analysis. The method comprises the steps of: measuring the impedance on said winding as a function of frequency, said measurement being represented in the form of a first voltage gain; comparing said impedance measurement with a reference measurement represented in the form of a second voltage gain, said comparison including a step of calculating three first parameters, each of said three first parameters being a correlation coefficient, between said first and second gains over three different frequency ranges. The method further comprises a step of determining the relative variation of at least a fourth parameter, said fourth parameter being a physical magnitude characteristic of said transformer, said relative variation being obtained by comparing said first and second gains.
Owner:ALSTOM TECH LTD

Parallelly connected capacitance type capacitance pressure sensor

The invention aims to provide a parallelly connected capacitance type capacitance pressure sensor which effectively solves the problems that a single capacitance pressure sensor fails to effectively increase capacitance relative variation due to limit on geometric dimensioning and has too large internal resistance and small SNR (signal to noise ratio) and the like. The sensor comprises a matched shell, a fixed electrode assembled with the matched shell, pipe-shaped extraction electrode, a moving electrode and a pressure extraction opening. The sensor is characterized in that the pressure extraction opening is one with a public welding base, two fixed electrodes and moving electrodes with the same specification assembled in the matched shell and a capacitance pressure sensor of the pipe-shaped extraction electrode are connected with one public welding base pressure extraction opening, the fixed electrode is connected with a lead wire to form the capacitance pressure sensor parallelly connected with two capacitance pressure sensors. The parallelly connected capacitance type capacitance pressure sensor has a rational structure design, multiples capacitance relative variation, remarkably improves sensitivity and SNR, is good in stability and high in measuring accuracy and reduces internal resistance, which enables the measuring range, compared with a single one, a constant upper limit and substantial extension in small and micro direction.
Owner:SHENYANG SENSOR TECH INST

Method for inspecting the surface of a moving strip by prior classification of the detected surface irregularity

A method for inspecting a surface of a moving strip to detect surface defects, which includes forming at least one digital picture of at least one face of the strip, in which the digital picture is made up of a set of successive rows of picture elements, each of which is assigned a digital value. The method also includes filtering the at least one digital picture to detect surface irregularities by detecting relative variations in the digital values, and processing the at least one filtered digital picture to identity a type of surface defect corresponding to each detected irregularity. Further, prior to the processing step, an overall characterization of each of the irregularities is performed by determining, a value of predetermined parameters characteristic of surface defects, and a prior classification of the irregularities is performed based on the determined values of the parameters, according to a set of predefined classes. The processing step is performed on each class, and the predetermined parameters characteristic of the surface irregularities is less than a total number of parameters used to identify the defect.
Owner:SOLLAC (SA)

Control device for internal combustion engine

Provided is a control device for an internal combustion engine which can suppress a relative variation in the fuel injection amount for each cylinder. A drive pulse width to drive the fuel injection valve for injecting the fuel is calculated according to a driving state of the internal combustion engine, any one or both of a valve-opening response delay time and a valve-closing response delay time with respect to a drive pulse signal of the fuel injection valve for each fuel injection value are calculated, and the drive pulse width is corrected to make an injection amount of each fuel injection valve matched to a predetermined injection amount based on any one or both of the valve-opening response delay time and the valve-closing response delay time calculated for each fuel injection valve.
Owner:HITACHI ASTEMO LTD

Brillouin scattering signal processing method and distributed fiber sensing system thereof

The invention relates to the technical field of intelligent sensing and particularly discloses a Brillouin scattering signal processing method and a distributed fiber sensing system thereof. The system comprises a sensing fiber, a laser signal source, an annular device, a detection pulse optical path modulation module, a frequency shift reference optical path modulation module, a coherent detection unit and a data acquisition processing module, so relative variation quantity of Brillouin frequency shifts can be precisely acquired, backward Brillouin scattering spectrums are acquired and the complete Brillouin scattering spectrum is obtained. The method comprises steps of firstly, establishing a detected Brillouin scattering signal spectrum model; and using a fast iteration algorithm based on numerical optimization to carry out characteristic extraction on the Brillouin scattering spectrum. In the method, scattering signal frequency spectrums obtained through frequency scanning of each time are fit, so sensing information of temperature or stress distributed along the fiber is precisely acquired. A solving method has strong global searching ability, so algorithm action time is shortened and measurement precision and timeliness of the system are effectively improved.
Owner:BEIJING AUTOMATION CONTROL EQUIP INST

Method and apparatus for recording/reproducing magnetization information

An information storage device having a hard disk has a metal probe that is brought closely to the surface of a multilayer film that includes a magnetic metal layer, a non-magnetic metal layer, and a magnetic metal layer up to a nano-meter order distance from the surface. The distance between the metal probe and the surface of the multilayer film, as well as the voltage to be applied are changed to change the state of the quantum well generated in the multilayer film, thereby changing the magnetizing direction relatively between the two magnetic metal layers. To read magnetization information from the hard disk, a change of an optically induced tunnel current is used. The change of the tunnel current is caused by a change of a plasmon resonance energy according to a relative change of the magnetizing direction between the magnetic metal layers.
Owner:HITACHI LTD

Dynamic phase alignment for resynchronization of captured data

A source synchronous external memory device returns data to a memory controller of an electronic device with its own clock signal, which allows the returned data to be captured with a high degree of accuracy. The captured data must then be resynchronized with the clock signal which controls the other components of the electronic device. This problem is particularly acute in the case of high speed memory devices, such as DDR (Double Data Rate) memory devices, and similar memory devices. Test data is written to the external memory device, and is then read back several times. Attempts are made to resynchronize the captured data with the system clock, with different relative variations in the phase of the captured data and the system clock, in order to select a value for the relative phase, which allows for optimum resynchronization.
Owner:ALTERA CORP

Rehabilitation robot control method based on joint stiffness and muscle fatigue

The invention discloses a rehabilitation robot control method based on joint stiffness and muscle fatigue. According to the rehabilitation robot control method, the joint angle signals and the surfaceelectromyogram signals of a subject are collected, individual physiological parameters of the muscles are identified through a genetic algorithm in combination with a positive and negative dynamics principle, a personalized joint skeletal muscle model is established, and joint stiffness information in the moving process is calculated; the median frequency of the surface electromyogram signal in the moving process is calculated, and the fatigue information of the subject is acquired by utilizing the relative variation value; and self-adaptive adjustment is carried out on the parameters of an impedance model by adopting the joint stiffness information and the motion fatigue information, meanwhile, the rigidity and the damping parameters are restrained through a saturation function, and theself-adaptive impedance control method of the rehabilitation robot is realized. According to the rehabilitation robot control method, the rigidity information related to joints and the fatigue information related to the muscles are considered at the same time, the rigidity information and the fatigue information are introduced into the rehabilitation robot for control, the safety of joints and muscles in the rehabilitation training process can be considered, and safe and effective rehabilitation training is realized.
Owner:WUHAN UNIV OF TECH

Device and method for measuring oil consumption of engine

The invention provides a device and method for measuring the oil consumption of an engine. The measuring device is composed of an oil filling tank, an observation window, an oil drain valve, an oil collecting tank, a vent pipe, a lifting platform, a camera, an electronic scale and the like. During measurement, when the working condition is in stable operation, the engine oil liquid level is relatively stable, and an oil level line which is flush with a valve opening in a visual oil level pipe is used as the basis reference. On the basis of the variation of the relative quality of engine oil added into the engine within a testing time period, the oil consumption of the engine within the testing time period is tested, and the relative variation of the oil weight is accurately measured through the accurate measurement and the zero clearing operation of the electronic scale. Meanwhile, measurement is conducted under the state that the engine is not stopped, the influence of operation condition difference of the engine and the oil storage amount difference of a filter under different working conditions on the oil consumption measurement result is avoided, and the measurement precision of the oil consumption of the engine is improved. In the testing process, it is guaranteed that the oil in the engine is placed above the normal operation liquid level, and the engine is prevented from being damaged.
Owner:CHERY AUTOMOBILE CO LTD

Observation method of crown settlement and periphery convergence of tunnel

The invention discloses an observation method of crown settlement and periphery convergence of a tunnel. The observation method comprises the following steps of: forming a new excavated section of the tunnel, then replacing a hanging hook by an ordinary reflective sticker, firmly sticking the ordinary reflective sticker as a measuring point on the wall of the tunnel, and marking in the center position of the sticker; measuring three-dimensional coordinates of the measuring point by using an ordinary engineering 2'' electronic total station through a prismatic-free measurement method, thus fast getting the relative variation of elevation and position according to the three-dimensional coordinate data values measured every time, and further knowing the crown settlement and the peripheral wall rock displacement variation. According to the method disclosed by the invention, the precision and the speed of the crown settlement and the periphery convergence during monitoring and measurement of the tunnel can be effectively improved, accurate data can be provided for construction of the tunnel and the construction can be guided.
Owner:CHINA MCC17 GRP

Despiking coefficient update method and device suitable for frequency hopping and power fluctuation system

The invention discloses a despiking coefficient update method and device suitable for a frequency hopping and power fluctuation system. The method comprises the following steps: when any carrier frequency point varies or the relative variation of the carrier power thereof is more than a set value, an offset pulse shaping filter coefficient is generated and the starting signal is updated; the filter power weighted correction factor of each carrier is determined according to the frequency variation of each carrier, the power-weighting calculation of the prototype filter coefficient of each carrier is performed; the cosine signal corresponding to each filter frequency point is generated according to the input frequency control word and phase control word of each carrier, time-domain multiplication-accumulation treatment is performed to the synchronized cosine signal and corrected prototype filter coefficient to obtain the offset pulse shaping filter coefficient; and the normalization, gain compensation and quantification treatment of the offset pulse shaping filter coefficient are performed, and the currently used offset pulse shaping filter coefficient of the system is updated. By adopting the invention, the despiking performance index of the system is matched with the static despiking performance index.
Owner:ZTE CORP

Variable valve control system for internal combustion engine

A variable valve control system for an internal combustion engine including a plurality of cylinders, the variable valve control system including a variable lift characteristic control mechanism to adjust a valve lift characteristic of each of intake valves. The variable valve control system is configured to perform determining an engine condition indicator in correlation with an actual relative variation in the valve lift characteristic between the cylinders; determining a desired valve lift characteristic in accordance with an operating condition of the internal combustion engine; controlling the valve lift characteristic of each of the intake valves in accordance with the desired valve lift characteristic; determining the engine condition indicator when the desired valve lift characteristic is equal to a predetermined small valve lift characteristic setting; and expanding the small valve lift characteristic setting if the determined engine condition indicator is larger than a predetermined first threshold value.
Owner:NISSAN MOTOR CO LTD

Raman optical spectrum method for identifying blackness handwriting

The invention provides a Raman spectrum method for identifying black handwriting, wherein, the method adopts ultraviolet laser light as an excitation light source; fluorescence is avoided through adopting ultraviolet laser light which directly irradiates handwriting; the Raman spectrum signals of corresponding handwritings on a detected material and a sample are respectively collected; whether the ink compositions of the handwritings are different or not can be identified from the difference of Raman peaks through comparison; moreover, the different written times of the handwritings can be identified through the relative variation of corresponding Raman peak strength. As for black handwriting containing carbon black, the forming time can be judged according to the ratio of the integral area of the Raman characteristic peak at 1600cm<-1> and the integral area of newly written handwriting at the same position. The method which is of great convenience realizes objective and actual identification without any damage on identified handwriting.
Owner:柯惟中 +2

Washing machine having balancer and method for controlling the same

A washing machine having a balancer and a control method thereof which achieve correct communication between a controller and a balancing module such that a balancing module is correctly shifted to a target position. The control method of the washing machine includes measuring a first time between position detection time points of the balancing modules during rotation of the rotary tub when the plurality of balancing modules is in a static mode, measuring a second time between position detection time points of the balancing modules during rotation of the rotary tub when any one of the balancing modules is shifted by a predetermined distance through a movement command, and confirming a relationship between a module ID of any one of the balancing modules and a communication ID of the movement command through a relative variation of the second time with respect to the first time.
Owner:SAMSUNG ELECTRONICS CO LTD
Who we serve
  • R&D Engineer
  • R&D Manager
  • IP Professional
Why Eureka
  • Industry Leading Data Capabilities
  • Powerful AI technology
  • Patent DNA Extraction
Social media
Eureka Blog
Learn More
PatSnap group products